Institut de Chimie Moléculaire et des Matériaux d'Orsay

Synthèse, Propriétés et Modélisation des Matériaux

Couches Minces Fonctionnelles

Animation : Vincent Ji

L’objectif général du groupe Couches Minces Fonctionnelles est de comprendre le développement de films et couches minces de stœchiométrie et microstructure contrôlées. Les relations entre paramètres d’élaboration, composition chimique, microstructure et propriétés fonctionnelles sont étudiées. Le rôle des contraintes internes sur la stabilité thermodynamique, chimique et sur les mécanismes d’endommagement est aussi un objectif majeur lorsque l'on s'intéresse à la durabilité des systèmes (couche/substrat). Nos études reposent sur une approche expérimentale multi-physique et multi-échelle et sur un couplage étroit avec les calculs de modélisation et simulation. Elles portent essentiellement sur des matériaux à fort potentiel technologique pour des applications telles que la microélectronique et l'optique (couches minces d’oxydes de zircone ou de vanadium et de pérovskite de type ABO3), protection contre la corrosion haute température (alliages métalliques complexes), nucléaire (oxydation naturelle de l’alliage de zirconium Zy4), capteurs électrochimiques (oxyde d’étain comme sous couche en vue d’un greffage électrochimique).

Notre groupe est composé de deux professeurs (Clotilde Berdin, Vincent Ji), de trois maîtres de conférences (Michel Andrieux (HDR), Corinne Legros, Nathalie Prud’homme), d’un technicien (Christophe Racic).

intro couches minces.png

Publications récentes du groupe

Surface characteristics and stress corrosion behavior of AA 7075-T6 aluminum alloys after different shot peening processes. L. Bao, K. Li, J. Zheng, Y. Zhang, K. Zhan, Z. Yang, B. Zhao, V. Ji, Surface and Coatings Technology, 2022, 440, 128481

Surface characteristic and wear resistance of S960 high-strength steel after shot peening combing with ultrasonic sprayed graphene oxide coating. Z. Yang, J. Zheng, K. Zhan, C. Jiang, V. Ji, Journal of Materials Research and Technology, 2022

Effect of Ti microparticles on the microstructure and properties of Ni-Ti composite coating prepared by electrodeposition. L. Wang, J. Ren, Y. Zhao, V. Ji, H. Liu, M. Liu, Z. Wang, C. Jiang, Z. Wang, Journal of Alloys and Compounds, 2022, 164313

Kinetics and energetics of room-temperature microstructure in nanocrystalline Cu films: The grain-size dependent intragrain strain energy. Z. Chai, X. Huang, Z. Yu, V. Ji, C. Jiang, X. Chen, Journal of Applied Physics, 2022, 131, 055301

Tribological Behavior and Corrosion Resistance of S30432 Steel after Different Shot Peening Processes. K. Zhan, Y. Zhang, S. Zhao, Z. Yang, B. Zhao, V. Ji, Journal of Materials Engineering and Performance, 2022, 31, 1250-1258

The synergistic role of Ti microparticles and CeO2 nanoparticles in tailoring microstructures and properties of high-quality Ni matrix nanocomposite coating. L. Wang, S. Xing, Z. Shen, H. Liu, C. Jiang, V. Ji, Y. Zhao, Journal of Materials Science & Technology, 2022

Mechanism of Blunt Punching Tools’ Influence on Deformation and Residual Stress Distribution. W. Wang, X. Fang, X. Wang, M. Andrieux, V. Ji, Metals, 2021, 11

Numerical homogenization and experimental study of the influence of graphite content and voids on the coefficients of thermal expansion of 2017 Aluminium matrix composites. M. Bhouri, F. Mzali, C. Berdin, F. Di Paola, Materials today communications, 2021, 26, 101638

Surface characteristic and wear resistance of QT-700-2 nodular cast iron after laser quenching combing with shot peening treatment. K. Zhan, Y. Zhang, L. Bao, Z. Yang, B. Zhao, V. Ji, Surface and Coatings Technology, 2021, 423, 127589

In- and out-plane transport properties of chemical vapor deposited TiO2 anatase films. A. Miquelot, L. Youssef, C. Villeneuve-Faure, N. Prud'Homme, N. Dragoe, A. Nada, V. Rouessac, S. Roualdes, J. Bassil, M. Zakhour, M. Nakhl, C. Vahlas, JOURNAL OF MATERIALS SCIENCE, 2021, 56, 10458–10476

Surface residual stress and microstructure evolutions of Hastelloy X alloy after severe shot peening. M. Chen, S. Xing, J. Li, J. He, Y. Lu, C. Jiang, V. Ji, Vacuum, 2021, 110136

Theoretical analysis and performance prediction on modified surface layer caused by ultrasonic surface rolling. Z. Liu, C. Zhang, H. Zhao, V. Ji, D. Wang, The International Journal of Advanced Manufacturing Technology, 2021

Unveiling the Residual Stresses, Local Micromechanical Properties and Crystallographic Texture in a Ti-6Al-4V Weld Joint. B. Mehdi, R. Badji, V. Ji, B. Alili, D. Bradai, W. Bedjaoui, F. Deschaux-Beaume, F. Brisset, Acta Metallurgica Sinica (English Letters), 2021

Multi-Scale Characterization by Neutronography and Electron Diffraction of Ni Coating on Cu-Ni-Al or Cast-Iron Glass Molds after Laser Cladding. F. Bourahima, A. L. Helbert, F. Ott, V. Ji, M. Rege, F. Brisset, A. Courteaux, T. Baudin, Materials Science Forum, 2021, 1016, 297-302

Toughening effects of Mo and Nb addition on impact toughness and crack resistance of titanium alloys. S. Huang, Q. Zhao, Y. Zhao, C. Lin, C. Wu, W. Jia, C. Mao, V. Ji, Journal of Materials Science & Technology, 2021, 79, 147-164

Microstructure evolution and mechanical properties of a lamellar near-α titanium alloy treated by laser shock peening. W. Jia, Y. Zan, C. Mao, S. Li, W. Zhou, Q. Li, S. Zhang, V. Ji, Vacuum, 2021, 184, 109906

Effects of ultrasonic surface rolling on fretting wear behaviors of a novel 25CrNi2MoV steel. Y. Zhang, L. Huang, F. Lu, S. Qu, V. Ji, X. Hu, H. Liu, Materials Letters, 2021, 284, 128955

Effect of stress shot peening on the residual stress field and microstructure of nanostructured Mg-8Gd-3Y alloy. H. Liu, X. Wei, S. Xing, L. Wang, W. Zhu, C. Jiang, V. Ji, K. Zhan, Journal of Materials Research and Technology, 2021, 10, 74-83

Residual Stresses and Microstructural Features of Rotary-Friction-Welded from Dissimilar Medium Carbon Steels. E. Priymak, Z. Boumerzoug, A. Stepanchukova, V. Ji, Physics of Metals and Metallography, 2020, 121, 1339-1346

Microstructure evolution and residual stress distribution of nanostructured Mg-8Gd-3Y alloy induced by severe shot peening. H. Liu, W. Zhu, C. Jiang, M. Guagliano, S. Xing, L. Wang, V. Ji, K. Zhan, Surface and Coatings Technology, 2020, 126465

Mechanical properties of CoCrCuFeNi multi-principal element alloy thin films on Kapton substrates. C.-H. Li, R. Dedoncker, L.-W. Li, F. Sedghgooya, F. Zighem, V. Ji, D. Depla, P. Djemia, D. Faurie, Surface and Coatings Technology, 2020, 126474

Microstructures and rolling contact fatigue behaviors of 17Cr2Ni2MoVNb steel under combined ultrasonic surface rolling and shot peening. Y. Zhang, S. Qu, F. Lu, F. Lai, V. Ji, H. Liu, X. Li, International Journal of Fatigue, 2020, 141, 105867

Influence of Y2O3 nanoparticles on microstructures and properties of electrodeposited Ni–W–Y2O3 nanocrystalline coatings. S. Xing, L. Wang, C. Jiang, H. Liu, W. Zhu, V. Ji, Vacuum, 2020, 181, 109665

Improved wear properties of NiTi nanocomposite coating with tailored spatial microstructures by extra adding CeO2 nanoparticles. L. Wang, S. Xing, H. Liu, C. Jiang, V. Ji, Surface and Coatings Technology, 2020, 399, 126119

Chemical vapor deposition of Cu films from copper(I) cyclopentadienyl triethylphophine: Precursor characteristics and interplay between growth parameters and films morphology. N. Prud'Homme, V. Constantoudis, A. E. Turgambaeva, V. V. Krisyuk, D. Samélor, F. Senocq, C. Vahlas, Thin Solid Films, 2020, 701, 137967

Determination of surface mechanical property and residual stress stability for shot-peened SAF2507 duplex stainless steel by in situ X-ray diffraction stress analysis. M. Chen, S. Xing, H. Liu, C. Jiang, K. Zhan, V. Ji, Journal of Materials Research and Technology, 2020, 9, 7644-7654

Evaluation of Mechanical Behavior and Surface Morphology of Shot-Peened Ti-6Al-4V Alloy. Y. Wen, P. Liu, L. Xie, Z. Wang, L. Wang, W. Lu, C. Jiang, V. Ji, Journal of Materials Engineering and Performance, 2020, 29, 182-190

Analytical modeling and experimental verification of surface roughness in the ultrasonic-assisted ball burnishing of shaft targets. Z. Liu, Q. Dai, J. Deng, Y. Zhang, V. Ji, The International Journal of Advanced Manufacturing Technology, 2020

Effect of shot peening on residual stress distribution and tribological behaviors of 17Cr2Ni2MoVNb steel. Y. Zhang, F. Lai, S. Qu, V. Ji, H. Liu, X. Li, Surface and Coatings Technology, 2020, 386, 125497

Atomic-scale investigation of the interface precipitation in a TiB2 nanoparticles reinforced Al–Zn–Mg–Cu matrix composite. Y. Ma, A. Addad, G. Ji, M.-X. Zhang, W. Lefebvre, Z. Chen, V. Ji, Acta Materialia, 2020, 185, 287-299

Morphological, structural, optical, and electrical study of nanostructured thin films: Charge transport mechanism of p-type Co3O4. A. Miquelot, M. Despotopoulou, C. Vahlas, C. Villeneuve, N. Dragoe, N. Prud'Homme, O. Debieu, Materials Chemistry and Physics, 2020, 240, 122059

Laser cladding of Ni based powder on a Cu-Ni-Al glassmold: Influence of the process parameters on bonding quality and coating geometry. F. Bourahima, A.-L. Helbert, M. Rege, V. Ji, D. Solas, T. Baudin, Journal of Alloys and Compounds, 2019, 771, 1018-1028

Structural, Half-metallic and Magnetic Properties of the Imperfect Pb2FeReO6 Containing Eight Different Inherent Defects. Y. Zhang, H.-X. Chen, L. Duan, L. Ni, J.-B. Fan, J. Wang, G.-T. Ci, V. Ji, Journal of Magnetics, 2019, Vol.24 , No.3,, pp.413-422

Optimization of Microstructural Evolution during Laser Cladding of Ni Based Powder on GCI Glass Molds. F. Bourahima, A. L. Helbert, V. Ji, M. Rege, A. Courteaux, F. Brisset, T. Baudin, Key Engineering Materials, 2019, 813, 185-190

Surface layer characteristics of SAF2507 duplex stainless steel treated by stress shot peening. M. Chen, C. Jiang, Z. Xu, V. Ji, Applied Surface Science, 2019, 481, 226-233

Roles of growth mechanisms of Ni deposits on corrosion behaviors of NixAlyTi composite coatings. Y. Zhao, S. Xing, L. Wang, Y. Sun, H. Liu, K. Zhan, C. Jiang, V. Ji, W. Li, Applied Surface Science, 2019, 492, 177-188

Surface layer microstructures and wear properties modifications of Mg-8Gd-3Y alloy treated by shot peening. H. Liu, C. Jiang, M. Chen, L. Wang, V. Ji, Materials Characterization, 2019, 158, 109952

TiO2 nanotree films for the production of green H2 by solar water splitting: From microstructural and optical characteristics to the photocatalytic properties. A. Miquelot, O. Debieu, V. Rouessac, C. Villeneuve, N. Prud'Homme, J. Cure, V. Constantoudis, G. Papavieros, S. Roualdes, C. Vahlas, Applied Surface Science, 2019, 494, 1127-1137

A new powder metallurgy routine to fabricate TiB2/Al–Zn–Mg–Cu nanocomposites based on composite powders with pre-embedded nanoparticles. Q. Yang, Y. Ma, Z. Chen, G. Ji, M.-L. Wang, S.-Y. Zhong, Y. Wu, V. Ji, H.-W. Wang, Materialia, 2019, 8, 100458

Effect of scandia content on the hot corrosion behavior of Sc2O3 and Y2O3 co-doped ZrO2 in Na2SO4 + V2O5 molten salts at 1000 °C. C. Chen, T. Liang, Y. Guo, X. Chen, Q. Man, X. Zhang, J. Zeng, V. Ji, Corrosion Science, 2019, 158, 108094

Modification of Fluorine-Doped Tin Oxide surface: optimization of the electrochemical grafting of diazonium salt. C. Cannizzo, A. Chaussé, C. Legros, V. Bui-Thi-Tuyet, M. Andrieux, Surfaces and Interfaces, 2019, 15, 110-116

Zirconia layers: Structure, residual stress and fracture strength. J. Djuidje-Dzumgam, C. Berdin, M. Andrieux, P. Ribot, Engineering Fracture mechanics, 2019, 214, 378-389

Prediction of the terminations and Miller planes of the tetragonal zirconia thin films as a gate dielectric layer in integrated-circuit industry. Y. Zhang, H.-X. Chen, L. Duan, L. Ni, J.-B. Fan, Z. Wang, V. Ji, Surface and Interface Analysis, 2019, 0

Studying the insulating characters of cubic ZrO2 slabs with nine terminations within three lower index Miller planes (001), (110) and (111). Y. Zhang, H.-X. Chen, L. Duan, J.-B. Fan, L. Ni, Z. Wang, H. Li, V. Ji, Microelectronic Engineering, 2019, 213, 77-85

Surface layer characteristics of SAF2507 duplex stainless steel treated by stress shot peening. M. Chen, C. Jiang, Z. Xu, V. Ji, Applied Surface Science, 2019, 481, 226-233

Influences of Al and Ti particles on microstructure, internal stress and property of Ni composite coatings. Y. Zhao, L. Wang, Y. Sun, H. Liu, C. Jiang, V. Ji, W. Li, Journal of Alloys and Compounds, 2019, 793, 314-325

Cube orientation bands observed in largely deformed Al-Sc alloys containing shearable precipitates. C.-Y. Dan, Z. Chen, G. Ji, S.-Y. Zhong, J. Li, X.-R. Li, F. Brisset, G.-A. Sun, H.-W. Wang, V. Ji, Scripta Materialia, 2019, 166, 139-143

Laser cladding of Ni based powder on a Cu-Ni-Al glassmold: Influence of the process parameters on bonding quality and coating geometry. F. Bourahima, A.-L. Helbert, M. Rege, V. Ji, D. Solas, T. Baudin, Journal of Alloys and Compounds, 2019, 771, 1018-1028

Investigation on microstructure and properties of Al18B4O33 whisker reinforced AlMgSi matrix composite after shot peening. H. Liu, M. Chen, L. Wang, K. Zhan, V. Ji, C. Jiang, Vacuum, 2019, 160, 303-310

Experimental study of the mechanisms of nanoparticle influencing the fatigue crack growth in an in-situ TiB2/Al-Zn-Mg-Cu composite. Y. Ma, J. Geng, Z. Chen, M. Wang, D. Chen, G. Ji, V. Ji, H. Wang, Engineering Fracture Mechanics, 2019, 207, 23–35

Experimental study on macro- and microstress state, microstructural evolution of austenitic and ferritic steel processed by shot peening. M. Chen, C. Jiang, Z. Xu, K. Zhan, V. Ji, Surface and Coatings Technology, 2019, 359, 511-519

Residual stress and microstructure evolutions of SAF 2507 duplex stainless steel after shot peening. M. Chen, H. Liu, L. Wang, Z. Xu, V. Ji, C. Jiang, Applied Surface Science, 2018, 459, 155-163

Evaluation of LaAlO3 as top coat material for thermal barrier coatings. N. Vourdas, E. Marathoniti, P.-K. Pandis, C. Argirusis, G. Sourkouni, C. Legros, S. Mirza, V.-N. Stathopoulos, Transactions of Nonferrous Metals Society of China, 2018, 28, 1582-1592

Investigations into the Surface Strain/Stress State in a Single-Crystal Superalloy via XRD Characterization. H. Duan, L. Qin, Y. Pei, S. Li, L.-D. Zhao, V. Ji, S. Gong, Metals, 2018, 8, 376

A comparison study of the Born effective charges and dielectric properties of the cubic, tetragonal, monoclinic, ortho-I, ortho-II and ortho-III phases of zirconia. Y. Zhang, H.-X. Chen, L. Duan, J.-B. Fan, L. Ni, V. Ji, Solid State Sciences, 2018, 81, 58-65

Investigation on the thermostability of residual stress and microstructure in shot peened SAF 2507 duplex stainless steel. M. Chen, H. Liu, L. Wang, Z. Xu, V. Ji, C. Jiang, Vacuum, 2018, 153, 145-153

Investigation on microstructure and properties of electrodeposited Ni-Ti-CeO2 composite coating. L. Wang, Y. Zhao, C. Jiang, V. Ji, M. Chen, K. Zhan, F. Moreira, Journal of Alloys and Compounds, 2018, 754, 93-104

Microstructure evolution and hot corrosion mechanisms of Ba2REAlO5 (RE = Yb, Er, Dy) exposed to V2O5 + Na2SO4 molten salt. L. Guo, C. Zhang, Q. He, J. Yu, Z. Yan, F. Ye, C. Dan, V. Ji, Journal of the European Ceramic Society, 2018, 38, 3555-3563

Simultaneously increasing strength and ductility of nanoparticles reinforced Al composites via accumulative orthogonal extrusion process. J. Liu, Z. Chen, F. Zhang, G. Ji, M. Wang, Y. Ma, V. Ji, S. Zhong, Y. Wu, H. Wang, Materials Research Letters, 2018, 6, 406-412

A comparison study of the structural and mechanical properties of cubic, tetragonal, monoclinic, and three orthorhombic phases of ZrO2. Y. Zhang, H.-X. Chen, L. Duan, J.-B. Fan, L. Ni, V. Ji, Journal of Alloys and Compounds, 2018, 749, 283-292

Cold rolling texture evolution of TiB2 particle reinforced Al-based composites by Neutron Diffraction and EBSD analysis. C.-Y. Dan, Z. Chen, M.-H. Mathon, G. Ji, L.-W. Li, Y. Wu, F. Brisset, L. Guo, H.-W. Wang, V. Ji, Materials Characterization, 2018, 136, 293-301

Investigation on surface layer characteristics of shot peened graphene reinforced Al composite by X-ray diffraction method. K. Zhan, Y. Wu, J. Li, B. Zhao, Y. Yan, L. Xie, L. Wang, V. Ji, Applied Surface Science, 2018, 435, 1257-1264

Hot corrosion behavior of TiO2 doped, Yb2O3 stabilized zirconia exposed to V2O5 + Na2SO4 molten salt at 700–1000°C. L. Guo, Z. Yan, J. Yu, C. Zhang, M. Li, F. Ye, V. Ji, Ceramics International, 2018, 44, 261-268

Evaluation of the residual stress and microstructure character in SAF 2507 duplex stainless steel after multiple shot peening process. M. Chen, H. Liu, L. Wang, C. Wang, K. Zhu, Z. Xu, C. Jiang, V. Ji, Surface and Coatings Technology, 2018, 344, 132-140

Surface layer characteristics of CNT/Al–Mg–Si alloy composites treated by stress peening. K. Zhu, C. Jiang, V. Ji, Surface and Coatings Technology, 2017, 317, 10-16

Microstructure study of cold rolling nanosized in-situ TiB2 particle reinforced Al composites. C.-Y. Dan, Z. Chen, G. Ji, S.-H. Zhong, Y. Wu, F. Brisset, H.-W. Wang, V. Ji, Materials & Design, 2017, 130, 357-365

Effect of the shot peening on the deformation of Al alloy component. X. Zhang, K. Liao, V. Ji, H. Chen, L. Hu, Surface Engineering, 2017, 0, 1-8

The Roles of Ti Particles in Improving the Corrosion Resistance of Electrochemically Assembled Ni-Ti Composite Coatings. Y. Zhao, L. Wang, Z. Qin, C. Wang, Z. Xu, C. Jiang, V. Ji, CORROSION, 2017, 73, 1107-1118

Structural, electronic, and magnetic properties of double perovskite Pb2FeReO6 thin films with (001) orientation and three possible terminations. Y. Zhang, L. Duan, V. Ji, Surface and Interface Analysis, 2017, 49, 960-966

Optimisation of microstructure and corrosion resistance of Ni-Ti composite coatings by the addition of CeO2 nanoparticles. L. Wang, M. Chen, H. Liu, C. Jiang, V. Ji, F. Moreira, Surface and Coatings Technology, 2017, 331, 196-205

Structure transformation of Ti films deposited on SiC single crystal substrates. L. Li, Y. Liu, X. Mao, L. Zeng, V. Ji, Materials Characterization, 2017, 134, 64-68

Residual stress and microstructure evolution of shot peened Ni-Al bronze at elevated temperatures. C. Wang, C. Jiang, M. Chen, L. Wang, H. Liu, V. Ji, MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2017, 707, 629-635

Hot corrosion behavior of Ba2REAlO5 (RE = Dy, Er, Yb) ceramics by vanadium pentoxide at 900–1000°C. C. Zhang, L. Guo, J. Yu, M. Li, F. Ye, V. Ji, Ceramics International, 2017, 43, 11944-11952

Effects of TiO2 doping on the defect chemistry and thermo-physical properties of Yb2O3 stabilized ZrO2. L. Guo, C. Zhang, L. Xu, M. Li, Q. Wang, F. Ye, C. Dan, V. Ji, Journal of the European Ceramic Society, 2017, 37, 4163-4169

Microstructure study of cold rolling nanosized in-situ TiB2 particle reinforced Al composites. C.-Y. Dan, Z. Chen, G. Ji, S.-H. Zhong, Y. Wu, F. Brisset, H.-W. Wang, V. Ji, Materials & Design, 2017, 130, 357-365

Calcium-magnesium-alumina-silicate (CMAS) resistance property of BaLn2Ti3O10 (Ln=La, Nd) for thermal barrier coating applications. L. Guo, M. Li, C. Yang, C. Zhang, L. Xu, F. Ye, C. Dan, V. Ji, Ceramics International, 2017, Volume 43, Issue 13, Pages 10521–10527

Hot corrosion behavior of (Gd0.9Sc0.1)2Zr2O7 in V2O5 molten salt at 700–1000 °C. C. Zhang, M. Li, Y. Zhang, L. Guo, J. Dong, F. Ye, L. Li, V. Ji, Ceramics International, 2017, Volume 43, Pages 9041–9046

Surface mechanical property and residual stress of peened nickel-aluminum bronze determined by in-situ X-ray diffraction. C. Wang, C. Jiang, Y. Zhao, M. Chen, V. Ji, Applied Surface Science, 2017, Volume 420, Pages 28–33

Surface layer characteristics of CNT/Al–Mg–Si alloy composites treated by stress peening. K. Zhu, C. Jiang, V. Ji, Surface and Coatings Technology, 2017, Volume 317, Pages 10–16

Thermal stability of residual stresses and work hardening of shot peened tungsten cemented carbide. C. Wang, C. Jiang, V. Ji, Journal of Materials Processing Technology, 2017, 240, 98-103

Estimation of microstructure and corrosion properties of peened nickel aluminum bronze. C. Wang, C. Jiang, Z. Chai, M. Chen, L. Wang, V. Ji, Surface and Coatings Technology, 2017, 313, 136-142

Residual stress analysis on oxide layers obtained by high temperature oxidation of Chromia-forming alloys. N. Li, J. Xiao, N. Prud'Homme, L. Li, V. Ji, Materials Research Proceedings 2, 2016, pp 365-370

EFFECT OF HEAT TREATMENT ON THE MICROSTRUCTURAL EVOLUTION IN WELD REGION OF 304L PIPELINE STEEL. Z. Boumerzoug, S. Hamza, V. Ji, Journal of Thermal Engineering, 2016, Vol. 2, No. 6, Special Issue 5,, pp. 1017-1022

Preparation of metal-ceramic composites by sonochemical synthesis of metallic nano-particles and in-situ decoration on ceramic powders. A. Poulia, P.-M. Sakkas, D.-G. Kanellopoulou, G. Sourkouni, C. Legros, C. Argirusis, Ultrasonics Sonochemistry, 2016, 31, 417-422

Key role of the short-range order on the response of the titanate pyrochlore Y2Ti2O7 to irradiation. G. Sattonnay, S. Cammelli, D. Menut, N. Sellami, C. Grygiel, I. Monnet, J. Béchade, J.-P. Crocombette, A. Chartier, A. Soulié, R. Tétot, C. Legros, P. Simon, S. Miro, L. Thomé, PHYSICAL REVIEW B, 2016, 94, 224109

XPS-nanocharacterization of organic layers electrochemically grafted on the surface of SnO2 thin films to produce a new hybrid material coating. R. Drevet, D. Dragoe, M.-G. Barthès-Labrousse, A. Chaussé, M. Andrieux, Applied Surface Science, 2016, 384, 442-448

Finite element modelling of the oxidation kinetics of Zy-4 with a controlled metal-oxide interface and the influence of growth stress. G. Zumpicchiat, S. Pascal, M. Tupin, C. Berdin, Corr. Sc., 2016, 100, 209-221

XPS-nanocharacterization of organic layers electrochemically grafted on the surface of SnO2 thin films to produce a new hybrid material coating. R. Drevet, D. Dragoe, M. G. Barthes-Labrousse, A. Chausse, M. Andrieux, Applied Surface Science, 2016, 384, 442-448

Modelling of liquid sodium induced crack propagation in T91 martensitic steel: Competition with ductile fracture. S. Hémery, C. Berdin, T. Auger, M. Bhouri, J. of Nuc. Mat., 2016, 481, 24-32

The half-metallic ferromagnetic characters of (001)-oriented thin films of the double perovskite Pb2FeMoO6. Y. Zhang, L. Duan, V. Ji, Thin Solid Films, 2016, 615, 318-323

The detailed crystal and electronic structures of the cotunnite-type ZrO2. Y. Zhang, L. Duan, V. Ji, Solid State Communications, 2016, 239, 27–31

Numerical analysis and experimental validation on residual stress distribution of titanium matrix composite after shot peening treatment. L. Xie, C. Wang, L. Wang, Z. Wang, C. Jiang, W. Lu, V. Ji, Mechanics of Materials, 2016, 99, 2–8

The detailed crystal and electronic structures of the cotunnite-type ZrO2. Y. Zhang, L. Duan, V. Ji, Solid State Communications, 2016, 239, 27-31

First-principles study of the structural, electronic, and magnetic properties of double perovskite Sr2FeReO6 containing various imperfections. Y. Zhang, L. Duan, V. Ji, K.-W. Xu, Chin. Phys. B, 2016, Vol. 25 Issue (5), 058102

The structural, electronic, and magnetic properties of the stoichiometric (001) surface of double perovskite Sr2FeMoO6. Y. Zhang, V. Ji, K.-W. Xu, Surface and Interface Analysis, 2016, 1040–1047

Microstructure and residual stresses in Ti-6Al-4V alloy pulsed and unpulsed TIG welds. B. Mehdi, R. Badji, V. Ji, B. Allili, D. Bradai, F.-D. Beaume, F. Soulié, Journal of Materials Processing Technology, 2016, 231, 441-448

Characterization on surface mechanical properties of Ti–6Al–4V after shot peening. L. Xie, Y. Wen, K. Zhan, L. Wang, C. Jiang, V. Ji, Journal of Alloys and Compounds, 2016, 666, 65-70

Effect of humidity on high temperature oxidation of AISI 430 stainless steel. N. Li, J. Xiao, N. Prud’Homme, V. Ji, Materials Science Forum, 2015, Vol. 833, pp 165-168

Modifications of structural and physical properties induced by swift heavy ions in Gd2Ti2O7 and Y2Ti2O7 pyrochlores. N. Sellami, G. Sattonnay, C. Grygiel, I. Monnet, A. Debelle, C. Legros, D. Menut, S. Miro, P. Simon, J.-L. Béchade, L. Thomé, Nuclear Instruments and Methods in Physics Research Section B, 2015, 365, 371-375

Rolling effect on serrated flow in an Al-Li-Cu-Mg alloy plate. R. Doglione, P. Haghi-Astiani, C. Berdin, Mat Perf Charac, 2015, 4, 4

Copper Refinement from Anode to Cathode and then to Wire Rod: Effects of Impurities on Recrystallization Kinetics and Wire Ductility. A.-L. Helbert, A. Moya, T. Jil, M. Andrieux, M. Ignat, F. Brisset, T. Baudin, Microscopy and Microanalysis, 2015, 21, 1153-1166

Metal organic precursor effect on the properties of SnO2 thin films deposited by MOCVD technique for electrochemical applications. R. Drevet, C. Legros, D. Berardan, P. Ribot, D. Dragoe, C. Cannizzo, M. G. Barthes-Labrousse, A. Chausse, M. Andrieux, Surface & Coatings Technology, 2015, 271, 234-241

Copper Refinement from Anode to Cathode and then to Wire Rod: Effects of Impurities on Recrystallization Kinetics and Wire Ductility. A.-L. Helbert, A. Moya, T. Jil, M. Andrieux, M. Ignat, F. Brisset, T. Baudin, MICROSCOPY AND MICROANALYSIS, 2015, 21, 1153-1166

Structural, electronic and magnetic properties of the Si chains doped zigzag AlN nanoribbons. J.-M. Zhang, J. Zhang, K.-W. Xu, V. Ji, Physica E: Low-dimensional Systems and Nanostructures, 2015, 65, 114-119

Finite element analysis of laser shock peening of 2050-T8 aluminum alloy. N. Hfaiedh, P. Peyre, H. Song, I. Popa, V. Ji, V. Vignal, International Journal of Fatigue, 2015, 70, 480-489

Effects of Co contents on the microstructures and properties of electrodeposited NiCo–Al composite coatings. F. Cai, C. Jiang, P. Fu, V. Ji, Applied Surface Science, 2015, 324, 482-489

Two stages for the evolution of crystallite size and texture of electrodeposited Ni–ZrC composite coating. Z. Zhang, C. Jiang, F. Cai, P. Fu, N. Ma, V. Ji, Surface and Coatings Technology, 2015, 261, 122-129

Hydrogen adsorption and storage on palladium-decorated graphene with boron dopants and vacancy defects: A first-principles study. L. Ma, J.-M. Zhang, K.-W. Xu, V. Ji, Physica E: Low-dimensional Systems and Nanostructures, 2015, 66, 40-47

Effects of vertical strain on zigzag graphene nanoribbon with a topological line defect. L.-H. Qu, J.-M. Zhang, K.-W. Xu, V. Ji, Physica E: Low-dimensional Systems and Nanostructures, 2015, 67, 116-120

Effects of Co contents on the microstructures and properties of the electrodeposited NiCo–Zr composite coatings. F. Cai, C. Jiang, Y. Zhao, V. Ji, Materials Research Bulletin, 2015, 65, 195-203

A first-principles study on uniaxial strain effects of nonplanar oxygen-functionalized armchair graphene nanoribbons. L.-H. Qu, J.-M. Zhang, K.-W. Xu, V. Ji, Journal of Alloys and Compounds, 2015, 631, 219-224

Fabrication and characterization of Ni–Zr composite coatings using electrodepositing technique. F. Cai, C. Jiang, Z. Zhang, E. Muttini, P. Fu, Y. Zhao, V. Ji, Journal of Alloys and Compounds, 2015, 635, 73-81

Characterization of the deformation texture after tensile test and cold rolling of a Ti-6Al-4V sheet alloy. B. Mehdi, H. Azzeddine, R. Badji, V. Ji, B. Alili, D. Bradai, IOP Conf. Series: Materials Science and Engineering, 2015, 82, 012018

A first-principles study on gas sensing properties of graphene andPd-doped graphene. L. Ma, J.-M. Zhang, K.-W. Xu, V. Ji, Applied Surface Science, 2015, 343, 121–127

Effects of the defects on the structural, electronic and magnetic properties of Sr2FeMoO6. Y. Zhang, V. Ji, K.-W. Xu, Journal of Alloys and Compounds, 2015, 648, 374-381

Residual stress distribution and microstructure in the friction stir weld of 7075 aluminum alloy. P. Ji, Z. Yang, J. Zhang, L. Zheng, V. Ji, V. Klosek, J Mater Sci, 2015, 50, 7262–7270

Quantitative study of particle size distribution in an in-situ grown Al–TiB2 composite by synchrotron X-ray diffraction and electron microscopy. Y. Tan, Z. Chen, A. Borbélyb, G. Ji, S.-Y. Zhong, D. Schryvers, V. Ji, H.-W. Wang, Materials Characterization, 2015, 102, 131–136

Effects of the defects on the half-metallic characters and magnetic properties in double perovskite Pb2FeMoO6. Y. Zhang, K.-W. Xu, V. Ji, Materials Chemistry and Physics, 2015, 162, 711-723

Study of ion diffusion in oxidation films grown on a model Fe–15%Cr alloy. A. C. S. Sabioni, J. N. V. Souza, V. Ji, F. Jomard, V. B. Trindade, J. F. Carneiro, Solid State Ionics, 2015, 276, 1–8

Internal stresses at the crystalline scale in textured ZrO2 films before lateral cracking. C. Berdin, S. Pascal, Y. Tang, J. Nuc. Mat., 2015, 460, 44-51